Vented vs Vent-Free Gas Logs: How to Choose
Quick answer
Vented gas logs are decorative: they burn a yellow, wood-like flame in a working wood-burning fireplace, with the damper open so exhaust goes up the chimney. Vent-free gas logs (also called ventless) are supplemental heaters: they run with the damper closed, keep their heat in the room and use an oxygen depletion sensor (ODS) to shut off if room oxygen drops. Choose vented for the most wood-like fire and large fireplaces; choose vent-free for heat, if your fireplace is approved for it, the room is big enough and local code allows it.
How each type works
Vented: damper open, exhaust up the chimney
Vented sets are decorative appliances for solid-fuel-burning fireplaces with a working flue. Certified sets are tested to ANSI Z21.60 or Z21.84; Hargrove notes vented sets may instead be tested to the Los Angeles RGA 2-72 standard, and some are not certified (Real Fyre, for example, offers ANSI certification on its G45 only in 16″ to 36″ sizes). The damper must be fully open whenever they burn, and a permanent damper clamp keeps it from closing fully. Carbon monoxide and soot from the flame leave through the chimney; if fumes or soot appear in the room, Grand Canyon says to stop using the logs and call a technician.
Vent-free: damper closed, room air, oxygen sensor
Vent-free sets are certified as unvented room heaters under ANSI Z21.11.2. They burn with the damper closed and use room air, so their combustion products, including water vapor, stay indoors. The model fuel gas code requires an oxygen depletion shutoff set no lower than 18% oxygen, caps input at 40,000 Btu/h and bars unvented heaters as a home’s only heat source.
Vented vs. vent-free at a glance
| Vented | Vent-free | |
|---|---|---|
| Certified as | Decorative appliance (ANSI Z21.60 or Z21.84 when certified; some sets RGA 2-72 or uncertified) | Unvented room heater (ANSI Z21.11.2) |
| Damper | Clamped open; fully open while burning | Closed (dual-listed sets can also run vented) |
| Fireplace | Wood-burning fireplace with a working flue | Masonry or listed factory-built fireplace approved for unvented logs, or a listed ventless firebox |
| Flame | Yellow, wood-fire look; some soot on logs is normal | Cleaner-burning, often bluer (your manual shows the normal flame); soot means call for service |
| Heat | Decorative, not rated as a heat source | Supplemental heat that stays in the room |
| Input examples | Real Fyre G46: 40,000-65,000 Btu/h | Real Fyre G9, G10, G18, G19A: 19,000-40,000 Btu/h (40,000 is the code maximum) |
| Sizes | Up to 60″ (Real Fyre G45) or 120″ (Grand Canyon) | About 16″ to 30″ |
| Local code | Installed per NFPA 54 and local building code | Restricted or banned in some states and cities |
Flame look vs. heat output
For looks, vented logs have the edge. Their burners make a yellow flame that imitates wood, soot on the logs is normal (Golden Blount, Hargrove), and sizes run far larger. The tradeoff is heat: they are decorative appliances, and Grand Canyon’s burner label reads “not a source of heat.” Hargrove also says not to close the damper partway for more warmth.
For heat, vent-free logs win. Hargrove notes that most vent-free sets use less gas yet deliver more heat to the home, because none of it is vented outdoors. The flame burns cleaner and is often bluer than a vented set’s, though some vent-free burners, such as White Mountain Hearth’s Slope Glaze, are designed to show yellow flames. Your manual shows what a normal flame looks like, and any soot means shut the set off and call a qualified technician.
Room-size and BTU limits for vent-free gas logs
Because a vent-free set burns room air, the International Fuel Gas Code limits all unvented appliances in a space to 20 Btu/h per cubic foot of room volume. Manuals state it as at least 50 cubic feet per 1,000 Btu/h, counting every gas appliance drawing air from the space (sealed direct-vent units excluded) and adjoining rooms joined by doorless openings. Real Fyre’s shortcut: length x width x ceiling height x 20 = maximum Btu/h.
| Set input | Minimum room volume | Floor area, 8 ft ceiling | Example |
|---|---|---|---|
| 30,000 Btu/h | 1,500 cu. ft. | About 188 sq. ft. | Real Fyre G18, 16/18″ set |
| 36,000 Btu/h | 1,800 cu. ft. | 225 sq. ft. | Real Fyre G9; Slope Glaze 24″ |
| 38,000 Btu/h | 1,900 cu. ft. | About 238 sq. ft. | Real Fyre G18, 24/30″ set; Slope Glaze 30″ |
| 40,000 Btu/h | 2,000 cu. ft. | 250 sq. ft. | Real Fyre G19A, 24/30″ natural gas |
Unusually tight homes need extra combustion air, such as a window opened 1″ to 2″ (Real Fyre).
Moisture and odor
Burning gas makes water. White Mountain Hearth’s manual puts it at about 1 ounce of water vapor per 1,000 Btu per hour, so a 36,000 Btu set on high adds roughly 36 ounces, a little over a quart, every hour. Real Fyre warns of moisture problems with long run times, especially in tightly built homes. If windows fog, open the damper or a window.
New logs give off some odor and smoke on the first burns as they cure and the paint bakes out, so ventilate the room. After that, odors usually come from vapors the flame burns, such as cleaners, paint, glue, cigarette smoke or new carpet. A raw gas smell is different: don’t light anything or touch switches; leave and call your gas supplier.
Safety: ODS, CO alarms and placement
- ODS: Real Fyre’s shuts the burner off before room oxygen falls below 18%. If it keeps tripping, call a technician; the shutoff point isn’t field-adjustable.
- CO alarms: The CPSC recommends them on every level and outside sleeping areas. Illinois law requires one within 15 feet of every room used for sleeping in homes that burn fossil fuel for heat, cooking or hot water or have an attached garage.
- Not in bedrooms or bathrooms: Hargrove’s vent-free manual rules them out, and the CPSC says never to run unvented fuel-burning appliances where people sleep.
- Attended, supplemental heat: Hargrove recommends not leaving a set burning unattended or while anyone is asleep.
- Warning signs: headache, dizziness and nausea are early signs of carbon monoxide poisoning (Real Fyre); get fresh air and stop using the appliance.
- Gas work is for professionals: leave installation, gas lines, valves and burner adjustments to a qualified installer, and have vent-free sets inspected yearly (Hargrove).
In fairness, manufacturers say certified sets emit well within accepted health and safety standards, while the Department of Energy’s Building America Solution Center recommends against unvented combustion appliances in homes because their byproducts and moisture stay indoors.
Check local code first
Vent-free logs aren’t allowed everywhere. California law bars selling unvented heaters for home use, except electric heaters and decorative gas logs for vented fireplaces. Baltimore’s building code prohibits unvented room heaters, and so does New York City’s fuel gas code. Manufacturers say to check state and local codes first; dual-listed sets can be installed vented where vent-free isn’t permitted. Local codes vary, so ask your village or city building department, including about permits, before you buy.
Which fireplaces accept which logs
Vented logs need:
- A solid-fuel-burning fireplace with a working flue that drafts properly.
- A chimney, damper and firebox cleaned and inspected before installation (see chimney cleaning and inspection).
- A permanent damper clamp and a big enough firebox and chimney. Real Fyre’s 24″ G46, for example, needs a 30″ front width, 24″ rear width, 15″ depth, 17″ height and at least 15 feet of chimney.
Vent-free logs need:
- A solid-fuel-burning masonry fireplace, a UL 127 factory-built fireplace listed for unvented logs, or a listed ventless firebox. If your fireplace manual says it wasn’t tested with unvented logs, it can’t take them.
- Clearances. Real Fyre’s G18 calls for 12″ of noncombustible material above the opening (10″ with a hood), 42″ to a combustible ceiling and 6″ to combustible side walls; otherwise the set must run with the damper open.
- A room that passes the size formula above.
With either type, keep glass doors fully open while burning, and never burn wood with gas logs installed.
Examples from brands we carry
- Real Fyre (vented): the G4 glowing-ember burner (12″ to 30″); the Real Fyre G45 Triple T burner, with an extra front burner for more flame and ember glow, up to 60″ (ANSI-certified versions run 16″ to 36″); and the G46, with hidden controls, 40,000 to 65,000 Btu/h depending on size.
- Grand Canyon (vented): sets from 18″ to 120″; styles include Grand Canyon Arizona Weathered Oak.
- Golden Blount (vented): Texas Bonfire Charred, 18″ to 36″, with see-through models.
- Hargrove: vented decorative sets plus dual-rated vent-free sets.
- Real Fyre (vent-free): G10 (19,000-37,000 Btu/h), G9 (21,000-36,000), the Real Fyre G18 vent-free burner (22,000-38,000) and G19A (23,000-40,000), all dual-listed for vented use.
- White Mountain Hearth (vent-free): the Slope Glaze vent-free burner tumbles gas through ceramic beads for a moving flame; 16″ to 30″, up to 38,000 Btu.
See more vented and vent-free gas log sets.
FAQ
Are vent-free gas logs safe?
Certified sets have an oxygen depletion sensor, and manufacturers say emissions are within accepted standards when installed and used as directed. They still put combustion byproducts and water vapor into the room, which is why Department of Energy guidance recommends against them and some cities ban them. If you choose one, size it to the room, keep it out of bedrooms, install CO alarms and have it inspected yearly.
Do vent-free logs need a chimney?
No. They run with the damper closed and can go in a listed ventless firebox with no chimney at all. In an existing fireplace, it must be a solid-fuel-burning masonry fireplace or a factory-built fireplace that has been tested, listed and labeled for unvented logs under UL 127, as the model fuel gas code requires.
Do vent-free logs smell?
Some odor and light smoke are normal on the first burns while the logs cure. After that, odors usually come from household vapors, such as cleaners, paint or new carpet, being burned by the flame. A raw gas smell means leave and call your gas supplier.
Can I convert vented logs to vent-free, or run vent-free logs vented?
You can’t convert a vented set: unvented use requires a set certified to ANSI Z21.11.2, and manufacturers say substitute parts void the certification. The reverse often works, since many vent-free sets are dual-listed for vented installation with the damper clamped open.
How can I tell which type I have?
Check the manual or the label on the burner. Vent-free sets are certified to ANSI Z21.11.2 and have an oxygen depletion sensor on the pilot; vented sets are labeled as vented decorative appliances, usually certified to ANSI Z21.60 or Z21.84 (some are tested to the Los Angeles RGA 2-72 standard or are uncertified). If you can’t find the paperwork, have a technician identify the set before you ever run it with the damper closed.
Not sure which type your fireplace can take? Visit our Downers Grove showroom at 1202-B 75th Street or call (630) 241-1919.