How to Light a Gas Fireplace (Pilot, Switch or Remote)
Quick answer: How you light a gas fireplace depends on its ignition. With electronic ignition there is no pilot to light by hand: you turn it on with the wall switch, remote, wall control or app, and the pilot and burner light automatically. On a standing-pilot (millivolt) fireplace, follow the lighting label on your unit; usually you turn the gas knob to OFF, wait the time on your label (often five minutes) and smell for gas, including near the floor, then turn it to PILOT, hold it in while pressing the igniter button until the pilot lights, keep holding about a minute, then turn the knob to ON and use the switch or remote. If you smell gas at any point, stop, don’t light anything, and leave.
These are the common steps manufacturers publish. Your own lighting label and manual come first, because wait times, hold times and switch positions vary by model. Empire puts its labels in the control compartment in the lower cavity; Napoleon’s sit by the valve behind the safety barrier and glass door.
First, the gas-smell rule
Before lighting, smell all around the fireplace, including next to the floor, since some gas is heavier than air (Empire, Heat & Glo and Real Fyre). If you smell gas, Majestic, Heat & Glo and Empire manuals say:
- Do not try to light any appliance.
- Do not touch any electrical switch or use any phone in your building.
- Leave the building immediately.
- Call your gas supplier from a neighbor’s phone. If you can’t reach them, call the fire department.
Nicor Gas adds: avoid anything that can spark, including cell phones and flashlights, and call Nicor Gas at 888-642-6748 (if Nicor is your utility) and 911 once you’re in a safe place. On propane, call your propane retailer, 911 or the fire department once you’re away (Propane Education & Research Council, PERC).
Empire, Napoleon and Real Fyre labels add two rules: use only your hand on the gas control knob, never tools or force (if it won’t push in or turn, call a qualified service technician), and don’t use the fireplace if any part has been under water.
Which ignition system do you have?
Look at the gas valve behind the lower access panel or front. Hearth & Home Technologies, maker of Majestic and Heat & Glo, says in its Heatilator manual that a standing pilot has a red or black igniter button and IntelliFire electronic ignition has none. If you’re unsure, ask your dealer.
| Ignition type | How to recognize it | How you turn it on |
|---|---|---|
| Standing pilot (millivolt) | Gas knob marked OFF, PILOT and ON, plus a red or black igniter (piezo) button. The pilot burns even when the burner is off. | Light the pilot at the knob (steps below), leave the knob on ON for the season, then use the wall switch, remote or on/off switch. |
| Electronic intermittent pilot ignition (IPI) | No igniter button; a control module and switch instead. The pilot normally lights only when you call for flame (some models also offer a continuous-pilot mode). | Wall switch, remote, wall control, thermostat or app (Majestic’s optional Wi-Fi module; Napoleon’s eFIRE Controller app). Never light it by hand. |
| Match-lit pilot (some gas log sets) | A log set whose label says the pilot can be lit by hand, such as some Real Fyre G45 sets. | Hold the knob in at PILOT while lighting the pilot with a long fireplace match or lighter, then turn to ON, with the damper fully open. |
How to light the pilot on a standing-pilot fireplace
Follow the lighting label on your own fireplace first; below is the common sequence on Empire, Napoleon and Heatilator labels.
- Turn everything off. Set the wall switch, remote or on/off switch to OFF and turn off any electric power to the fireplace. Napoleon also has you remove the remote’s batteries and set any thermostat to its lowest setting. Remove the screen or panel as your manual shows.
- Turn the gas knob to OFF. Push it in slightly and turn it clockwise. Don’t force it.
- Wait, then smell. Wait the full time on your label: five minutes on Napoleon, Heatilator and Real Fyre labels, ten on Empire’s DVCD fireplaces. Then smell for gas, including near the floor. If you smell gas, stop and follow the steps above.
- Turn the knob to PILOT. Turn it counterclockwise. Empire says to find the pilot by following the metal tube from the gas control.
- Push in and spark. Push the knob all the way in, hold it, and press the igniter button repeatedly until the pilot lights. Heatilator says that if it hasn’t lit after 10 seconds, turn the knob back to OFF and wait again.
- Keep holding. Hold the knob in about one minute after the pilot lights, then release. It pops back out and the pilot should stay lit. If it goes out, turn the knob back to OFF and start again from step 2, including the full wait.
- Turn the knob to ON. Turn it counterclockwise, replace the screen or panel, and restore power and remote batteries.
- Turn on the flame with the wall switch, remote or on/off switch. Empire says to leave the knob on ON through the heating season so the pilot stays lit.
Stop if the knob doesn’t pop back up when released (call a service technician or your gas supplier right away), or the pilot won’t stay lit after several tries (turn the knob to OFF and call), per Empire and Real Fyre.
Match-lit gas log pilots
Real Fyre G45 vented log sets with a hand-lit pilot work the same way, but you light the pilot with a long-stem match or long-necked butane lighter instead of a button. G45 versions with an ignition device are labeled not to be lit by hand. Real Fyre’s safety pilot kit instructions say the damper must be fully open whenever the logs burn. Light by hand only if your label says to.
How to turn on a gas fireplace with electronic ignition
Heat & Glo’s IPI label says to wait five minutes for any gas to clear and smell for gas, including near the floor, then turn the wall switch to ON, press ON or FLAME on the remote or wall control, or set the thermostat. If it doesn’t light after three tries, call your service technician or gas supplier.
- Module switch: Majestic’s IntelliFire Touch module has an ON/OFF/REMOTE switch. It must be on REMOTE for the wall switch or remote to work. Majestic warns never to cycle it more than once in five minutes, because gas may accumulate.
- Power outages: IntelliFire systems take backup batteries during an outage: two D cells on a Heat & Glo gas insert, four AA on Majestic’s MER36MN. On that Heat & Glo insert, the hand-held remote won’t work on battery power.
If it still won’t light: quick owner checks
Start with these owner-level checks:
- Batteries and power. Replace the batteries in the remote and receiver. Valor notes that low batteries shut its fire off completely. IntelliFire ignition needs household power, or its backup batteries in an outage.
- Switches. Check the wall switch and the control module switch (REMOTE on Majestic’s). On Empire millivolt fireplaces, if the remote’s batteries die, moving the REMOTE/OFF/ON switch to ON gives you heat.
- Gas valve and knob. The manual shutoff valve must be open (Napoleon’s is on the flexible gas connector), and a standing-pilot knob must be on ON, not PILOT.
- Propane level. If the tank ran out, don’t relight. PERC says a propane retailer or qualified professional must leak-check the system, restore service and relight pilots if needed. Never turn the gas on at the tank yourself.
- Remote pairing. A replacement remote or receiver must be paired to the fireplace; Majestic’s module has to be on REMOTE to pair, and the steps are in the remote’s manual. Need one? See our fireplace remotes and wall switches.
For anything past these basics, such as a pilot that lights while the burner won’t, or a pilot that keeps going out, use the symptom table in our guide to common fireplace problems and how to fix them, which covers why a gas fireplace won’t turn on and when to call a technician, and the gas fireplace maintenance checklist covers seasonal upkeep.
When to stop and call a qualified technician
- You smelled gas. Stay out until emergency personnel say it’s safe; on propane, have the whole system checked before using any appliance again (PERC).
- The gas knob won’t push in, turn by hand or pop back up.
- The pilot won’t stay lit after several tries, electronic ignition fails after three tries (Heat & Glo), or a lockout keeps returning (Majestic).
- Any part has been under water, or your propane tank ran out.
- The pilot is hard to light or keeps going out. PERC’s propane safety guide says never to try to fix or troubleshoot that yourself.
Leave the gas valve, pilot assembly, thermocouple and thermopile to a technician; that’s the job of our fireplace maintenance and repair service. And keep carbon monoxide alarms on each level of the home and outside sleeping areas, as the U.S. Consumer Product Safety Commission recommends.
Frequently asked questions
Where is the pilot light on a gas fireplace?
Inside the firebox, next to or behind the main burner (Empire’s sits behind the burner on the right); the gas knob is in a separate control area, often behind a lower access panel. Empire says to find it by following the metal tube from the gas control. Electronic-ignition pilots light themselves, so you don’t need to reach them.
How long do you hold the knob to light a gas fireplace pilot?
About one minute after the pilot lights, on Empire, Napoleon and Real Fyre labels, then release it. Follow the time on your own label.
Can I light a gas fireplace with a match?
Only if your label says so. Real Fyre documents match or lighter lighting for some log set pilots, while Heat & Glo’s electronic-ignition label says never to try to light the burner by hand.
Can I turn on my gas fireplace during a power outage?
Many can. Heatilator says standing-pilot wiring doesn’t need household power, and Heat & Glo and Majestic IntelliFire models take backup batteries, though some features, such as the remote, may not work.
How long should I wait before relighting a gas fireplace?
The full time on your label: five minutes on Napoleon, Heat & Glo, Heatilator and Real Fyre labels, and ten minutes on Empire’s DVCD series.
Not sure which ignition system you have? Bring a photo of the controls to our Downers Grove showroom at 1202-B 75th Street, or call (630) 241-1919.